Disclaimer: The following material is being kept online for archival purposes.

Although accurate at the time of publication, it is no longer being updated. The page may contain broken links or outdated information, and parts may not function in current web browsers.



 

(E25)   Electric Power Technology     

Who invented it?

1832 magneto In a 2008 letter, a user of the site "Exploration of the Earth's Magnetosphere" asked:
    I am tired of people telling me that Tesla invented alternating current. I know it must have been known by 1833 when a handful of people were spinning magnets near electromagnets to invent dynamos and motors. Who deserves the credit?
The answer:
    "Nikola Tesla certainly did not invent AC--he was primarily the engineer who helped George Westinghouse create his AC network, while Charles Proteus Steinmetz seems to have had a similar role in General Electric. I come from central Europe and vaguely recall reading that Siemens introduced it in the mid-1800s, but it probably happened independently at several places at once (see below). Faraday could have pursued AC around 1833...but the actual introduction was delayed by the simple reason that no one actually needed an electric network. There was no electric lighting, telegraphs worked off batteries, and machinery worked off steam engines--often with power distributed (e.g. in factories) by long shafts from which pulleys turned long leather belts to various machines."

switch on 1832 magneto
    In fact, Hippolyte Pixii built in 1832 a practical magneto (above). It generated AC, but a rotating switch reversed connections each half-turn, creating a current which could charge batteries (image on right)/. Later generators replaced the permanent magnet with a rotating electromagnet (powered by the part of the current generated), turning in the field of another electromagnet, somewhat like the coil described earlier for the galvanometer. But there existed no wide need for electricity.

    James Prescott Joule experimented around 1840 with electric motors driven by batteries. According to the New World Encyclopaedia on the internet :

    He went on to establish that, compared to the quantity of coal needed to produce 143 foot-pounds of work (a foot pound is the energy expended in raising a body weighing one pound, by one foot), an equal quantity of zinc used up in an electric battery would only produce 80 foot-pounds. From these results, Joule showed it would cost twenty times as much for an electric motor to do the same work as a steam engine.

Electric Light

    The situation changed rapidly around 1880. First, Thomas Alva Edison introduced the electric lightbulb in 1879. Many independent inventors designed similar lamps, but Edison vigorously promoted his lamp commercially and built DC power stations for his customers. Edison's lamp used a spiral carbon filament, produced by charring a strip of bamboo, in a glass bulb from which all air had been pumped. The lamp which dominated the 20th century was introduced in 1902 later by the Austrian Carl Auer von Welsbach, with had a metal filament (nowadays made of tungsten, which can stand high temperature). Rather than vacuum, filament lamps now containe the inert gas argon, which forms close to 1% of the Earth's atmosphere.

    Electric motors also turned out to be extremely convenient for transportation. Urban trolleys ("streetcars") spread widely, replacing horse-drawn ones and cable cars like the ones preserved in San Francisco, and elevated steam railroads. Most important, they were the only feasible propulsion for underground urban railroads ("subways"). Many other uses also used them--elevators, cranes and so forth.

The "War of Currents"

    Edison's network provided about 110 volts DC, which fit his lightbulbs and could be provided over short urban distances with no great loss. Nikola Tesla recognized the advantage of AC--in fact using several coils on the same dynamo to generate more efficient "polyphase" AC whose wave cycles were independent. The big advantage of AC was that transformers could convert electricity to high voltage (very efficiently!) and use much less copper in its distribution network. It was first developed in Europe, but George Westinghouse, who got wealthy by inventing an air brake for trains, brought the system to the US and hired Tesla to develop it. Electric lights could operate on either AC or DC, AC motors were at least as efficient as DC ones, and gradually AC prevailed. After a short but nasty public rivalry Westinghouse beat out Edison's "General Electric," in bids for the Niagara power station and the lighting of the 1893 World's Columbian Exposition. In the end General Electric itself switched to AC, guided by Charles Proteus Steinmetz who also developed the theory of AC circuits.

Iron

    One wonders whether electric technology would have evolved as vigorously, if not for the special properties of iron--properties known as ferromagnetism (the prefix "ferro-" signifies iron, though a few ferromagnetic alloys contain none). Iron made possible permanent magnets and compass needles, and generous amounts of it in electric motors and transformers greatly increase magnetic forces. This is because the iron atom is magnetic, thanks to the magnetism of electrons it contains.

    Actually, many other atoms are also magnetic, but their magnetic axes are usually randomly oriented-- a strong magnetic field will line them up somewhat and get somewhat reinforced ("paramagnetism"), but not by much. Ferromagnetic atoms spontaneously line up with each other, in chunks known as magnetic domains. In a strong field these domains line up magnetically and drastically reinforce the magnetic properties. In some materials--such as steel, hard elastic iron with 0.5-1% dissolved carbon--they can stay lined up and create permanent magnetism. In material like soft bendable wrought iron (low carbon content) they slip back to disorder (they also do so in permanent magnets if sufficiently heated).

    Lodestones are natural magnets, occasionally found, rich in iron compounds. They are believed to originate when a suitable mineral is struck by lightning, whose strong electric current, though very brief, creates an sufficient magnetic force. .

    Soft iron concentrates magnetic field lines and therefore produces strong magnetic forces in the areas where they emerge from the metal. Laboratory magnets sometimes have conical pole-pieces with the ends of the cones flat, missing the sharp tip. Such pole pieces are like funnels for magnetic flux, concentrating it to a smaller area to create a more powerful field.

    Of course, any ferromagnetic concentration of magnetic field lines has a natural limit: when all magnetic domains are lined up, the iron is saturated by the magnetic field and can no longer add to it.

Transformers

transformer     Have you ever opened an electrical transformer? (See image. Disconnected and discarded?) You will have noted several things.

    First, the shape of the iron core: it is probably shaped like the letter H, with extra iron bars added across the top and the bottom, and coils that go around the central bar of the H (in the image, that bar is vertical). The "primary coil" wrapped around that bar receives AC and produces in the bar an alternating magnetic field, which is then picked up by the "secondary coil" also wrapped there. In the operating range, the ratio V2/ V1 between output and input AC voltages is also the ratio N2/ N1between the numbers of windings in each coil:

V2/ V1   =   N2/ N1
The high efficiency of the transformer depends in part in confining all magnetic flux to the iron yoke.

    Second, notice that the magnetic core is not solid but is built up from many thin sheets of iron, covered with an insulating paint and stuck together. In addition to its magnetic properties, iron is also a conductor of electricity: if a solid core were used, electric currents would circulate not only in the secondary coil but also in the core, limited by Ohm's law and wasting their energy as heat. The paint breaks up such parasitic circuits and prevents currents on all but the smallest scales (where their effect is small). For a similar reason, many other AC devices (e.g. motors) have cores of insulated iron plates. If the device emits a deep hum (at the AC frequency of 60 cycles), some plates may be loose and vibrating, usually a sign of deterioration.

    And third, you better take care selecting the exact iron alloy you use. Steel can be magnetized permanently: it is not a good choice for a transformer core, expected to reverse its magnetization 120 times each second! In fact, the less your iron "remembers" its previous magnetization, the better it is suited for a transformer core. This "memory" is known as hysteresis ("lag behind"), and is graphically depicted by a plot of B, the magnetic field (or flux) without assistance of the core, against H, the value with such assistance (loosely defined; formulas also exist). The plotted scales for B and H need not be the same.

Hysteresis loop

    Suppose you start at point A, where the iron is unmagnetized. As the magnetizing current grows, both B and H rise proportionally, but ultimately the magnetization of the iron saturates at point B. From there B and H can still grow, but they go together, with no extra help from the iron core.

    Past the peak of the AC cycle, the current I causing the magnetization weakens and reverses, but the curve lags behind. At point C, when I=0, B=0 too, but H still "remembers" the old polarity, and will not reverse until the reverse current is large enough. The process now repeats the same variation with the opposite polarity, tracing every AC cycle a closed "hysteresis curve." An energy loss is associated with this forced reversal and can be shown to be proportional to the area inside the curve. The lost energy appears as heating. Large transformers serving the electrical grid need to be cooled, by enclosing them in tight containers (sometimes with cooling fins sticking out) filled with insulating oil. If a transformer in your home starts running hot, perhaps it needs replacing.

    With all that technology, transformers achieve high efficiency, typically 95%. They are most efficient if the load is small, when the B-H curve approximates a straight line and the operating point just shuttles back and forth along it, leaving little area in the middle.

Fluxgate Magnetometers

    Among a family of ferromagnetic materials known as ferrites some exist with a very abrupt onset of saturation. Their hysteresis contours are almost rectangular, and saturation always occurs at the same flux density.

Fluxgate

    Imagine two identical coils of insulated wire, driven by the same AC current and wrapped around on identical and parallel ferrite rods cores--but winding in opposite directions (the drawing shows the design of an instrument for the NASA Mars mission). Under ordinary circumstances, their magnetic fluxes will be equal and opposite; an additional coil, wrapped around the pair on its outside, will detect no net magnetization, and by Faraday's law of induction, no e.m.f is induced in it. If the cores undergo saturation at the same point in the AC cycle, their magnetic fluxes will still cancel and no e.m.f. is detected by the additional coil.

    If however an outside magnetic field exists at that location, with a component B1 in the direction of the rods, in one of them it will add to the magnetic flux in its direction, in the other, subtract from it. Therefore one rod will saturate a little ahead of the other in the AC cycle, and the other a little afterwards, creating an e.m.f. signal which can be detected. With suitable design, this signal gives a very sensitive measurement of thc component B1. To detect all three components, of course, requires 3 pairs of rods in mutually perpendicular directions. The pair of rods can also be replaced by a ring core of ferrite (see below), one side of which has N clockwise turns and the other N counterclockwise ones (as seen from the same side), of the same insulated wire.

Ring Fluxgate

   

    Several people pursued this detection method in the 1930s, but the most successful was probably Victor Vacquier. Until then, measurements of the magnetic field of Earth relied on some sort of suspended magnetic bar or needle: the fluxgate instrument allowed measurements to be pursued aboard airplanes and ships, and later aboard spacecraft as well. Warships could detect iron submarines under water (one reason the Soviet Union switched to the metal titanium). Magnetic surveys could be carried out at sea, discovering conclusive evidence of plate tectonics and the record of reversals of the north-south polarity of the Earth's magnetism going back many millions of years. In space fluxgates monitored the very weak magnetic field of interplanetary space and also surveyed magnetic fields of other planets. The sensitivity of such instruments extends to fields weaker than a millionth of the Earth's surface field.

    For another interesting story of the use of such an instrument, see "About Electronic Magnetometers and about Smoking."



 

Next Stop: E26. AC Impedance.htm  

Home Page "All Things Electric and Magnetic"
"From Stargazers to Starships"
Timeline of "All Things Electric and Magnetic"
Timeline (from "Stargazers")
Master index file

Author and Curator:   Dr. David P. Stern
    Mail to Dr.Stern:   stargaze("at" symbol)phy6.org .

Last updated: 29 July 2010


Above is background material for archival reference only.

NASA Logo, National Aeronautics and Space Administration
NASA Official: Adam Szabo

Curators: Robert Candey, Alex Young, Tamara Kovalick

NASA Privacy, Security, Notices